Home
Search results “Tianma car repair books online free”
How to Replace the Xiaomi Mi Max Screen
 
20:00
Click it here to buy: https://goo.gl/lpzcuh Website: http://www.honorbuy.com Facebook: https://www.facebook.com/honorbuycom Google+: https://plus.google.com/u/0/+XiaoMiShopcom Forum: http://www.honorbuy.com/forum
Views: 271210 Honorbuy Mobile Shop
DIY: Restoring Sealed Lead Acid Battery
 
06:55
Next Battery Repair Video http://www.youtube.com/watch?v=AS6Lyft8nfY this battery was very stubborn but its very stable now, so it was worth it. it was at 0.2 volts when i first got it. if your wanting to baby your battery, use distilled water instead of tap water, but i dont think it matters because these batteries where headed to the dump anyway.
Views: 339612 Rinoa Super-Genius
Raspberry Pi 7'' LCD Installation
 
08:01
find this kit here: http://www.sainsmart.com/7-inch-tft-lcd-monitor-for-raspberry-pi-touch-screen-driver-board-hdmi-vga-2av.html Follow us on facebook:https://www.facebook.com/SainSmart
Views: 1724790 SainSmart
Slovakia 2015 - Q3, On Board with Rob Huff
 
02:05
Slovakia Ring, 20/6/2015. Copyright: LADA SPORT ROSNEFT, 2015.
Electric Scooter Motor Test
 
00:49
Typical 250 watt Chinese made scooter motor I took off an electric scooter that was junked. I'm testing this using a car battery charger with a capacitor in parallel to smooth the charger output. I may eventually use this on a homemade scooter or pocket-bike Maker: Unite Motor Co LTD Model MY1016 Permanent Magnet DC 24 vdc 14amp 250 watt 2500RPMs
Views: 121560 yuandrew
Glass Tools: Glass Cutters and When to Use Oil
 
03:58
Delphi instructor Jeannette Woodard shows viewers a variety of different glass cutters, demonstrates how to hold them and explains when to use cutting oil. http://bit.ly/IGF48K
Basic Glass Cutting
 
04:45
Here I am doing basic glass cutting on a scrap piece of glass, actually it's a mirror. For much more videos about basic glass cutting, etc. see the playlist: http://www.youtube.com/playlist?list=PL4A57AB2EFB9566F9&feature=plcp Do not attempt to cut (pre) Tempered Glass, it cannot be cut and is designed to shatter to small pieces for safty purposes. You can cut (flat) Plate Glass. The "glass cutter" does not actually cut through the glass, it just scratches or "scores" it, so it should be called either a "glass scratcher/scorer" or a "tool of glass cutting". The score is then used when you actually break or snap the glass along this "weakened" line (or even curves are possible). Technically, you try to "bend" both sides along the score downward to "open" (not compress) the crack up to the back side of the glass. In the vid. I show holding the piece of glass with my hands as a lot of people seem to do - especially with small pieces, but it's safer to put the glass on a firm surface first and/or wear gloves. To remove the sharp parts after cutting the glass, I used some sandstone I found down by the river. Just about any stone or cement will do, just dont use something too hard like smooth quartz since it tends to just "glide" over the glass. Use both straight and circular motion with the stone at about a 45 degree angle to the glass to bevel it to a non-sharp/thin semi-round surface. It is good though to have an electric grinder or rotary tool like a Dremel incase the break leaves some sizeable bumps of glass areas that would be difficult to grind by hand. If you dont have that, perhaps a larger piece of smooth cement might work ok. Be sure to sweep up and vacuum any glass shards. Note you can use a flat rule made of metal, wood, or plastic to guide the glass cutter, but be sure its not too thin since you do not want to damage the "cutting wheel" (the part that scores the glass) if it came in contact with metal. About the tool I made; the ruler-straightedge with the rubber attached to the back. The rubber (or nylon) was cut from a bicycle inner-tube, and was attached with contact cement which is very sticky and somewhat flexible. This glue is sometimes called "rubber cement". I got a tube for about $1. I also lightly scratched both surfaces of the rubber for better adhesion of the glue and for better "holding" ability on the glass. I guess you could also use some flat erasor type material too instead of the inner tube material. Silicone rubber or a thin coat or beads of dried caulking might be ok. Some tape can possibly be used to secure the straightrule, but you might have to clean up any residue left from the tape unless you put the tape right on the rule itself. When you cut the bicycle tube, avoid breathing the powder (usually talc or talcum), so rinse the tube segment with hot soapy water and let it dry. Keep the "scoring wheel" oiled. I just keep/store that end in a glass with some clear oil in it. I use cheap "mineral oil" from the dollar/drug store. Find some flat glass pieces and practice a bit on them so that you are prepared to cut glass when you need to. Here is a good website about glass cutters, care and use: http://www.freepatternsforstainedglass.com/your-glass-cutter.html
Views: 394070 Jon
WTCC 2012 Macau Oriola, Michelisz Unfall
 
01:21
Pepe Oriola schißt Norbert Michelisz Einfahrt Lisboa ab. Michelisz rumpelt so blöd über den Curb, dass er ihn aus den Boden reißt.
Views: 991 Racing15528
Maybelline Commercial w/  Gerald Anderson
 
01:02
Newest promo of Maybelline visit at http://begeraldsgirl.com/site/home
Views: 32603 diatienza