I show how easy it is to change a water pump on a 2004 Chevy Tahoe 5.3L. Never be afraid to challenge any task and never ever give up. Put Jesus at the center God Bless.
Views: 142295 oldskool funk
I SHOW MY METHOD FOR CHECKING VALVE AND VALVE SEATING (OTHER THAN THE CYLINDER LEAK DOWN TEST WHILE THE HEAD IS ON THE CAR) FOR ANY LEAKAGE WHILE THE CYLINDER HEAD IS OFF THE VEHICLE SO YOU DON'T HAVE TO GUESS IF WHETHER OR NOT YOU NEED TO GRIND THE VALVES. BUT IF YOU GO THROUGH ALL THE HARD WORK OF PULLING OFF THE HEAD THEN YOU MIGHT AS WELL GRIND ALL THE VALVES AND SEATS. THIS IS JUST SHOWING YOU PROOF THAT YOU CAN STILL CHECK FOR LEAKAGE WHILE THE HEAD IS OFF THE ENGINE BLOCK BY SIMPLY USING WATER AND AIR. KEEP IN MIND PITTED SEATS, BENT VALVES, WARPED HEAD, BAD VALVE GUIDES AND A FEW OTHER FACTORS CAN ALSO CONTRIBUTE TO A LEAKING VALVE & SEAT. IF YOU DO NOT HAVE AN AIR COMPRESSOR THEN TRY COMPRESSED AIR IN A CAN USED FOR CLEANING COMPUTERS (THEY SELL THEM AT WALMART) BUT MAKE SURE YOU USE A LONG STICK NOZZLE TO APPLY AIR RIGHT BEHIND THE SEAT EDGES JUST LIKE I DO IN THE VIDEO. GO GET IT! STAY STRONG AND NEVER LET ANYTHING OR ANYONE CRUSH YOUR FAITH IN JESUS CHRIST OR YOUR WILL TO WIN!
Views: 100881 oldskool funk
This is how to change brake pads on a 2009 dodge avenger. Its simple but be careful when spinning the rotor in the air if you do it the way i showed in this video while sanding off the glaze, Keep your head up and God Bless. Jesus is the reason.
Views: 69175 oldskool funk
This is how to resurface a cylinder head at home using sandpaper a flat sanding block flat straight glass and thick board never be afraid to challenge a task and never back down. God Bless
Views: 989344 oldskool funk
This is how to diagnose a blown head gasket or cracked cylinder head the principle is the same for all vehicles Stay strong in Jesus Christ, God Bless
Views: 732859 oldskool funk
This is one of the easiest ways to check if you have a blown head gasket with no specialized tools. its simple and easy for the DIYer. Put Jesus Christ at the center of your life and never ever give up!
Views: 1286877 oldskool funk
This is how I find TOP DEAD CENTER on the COMPRESSION STROKE. Its simple and fast. Not as hard as it seems God Bless
Views: 82295 oldskool funk
I show you how to change a light bulb on a 2004 Chevy Tahoe in less than 5 Minutes hope it helps you out God Bless.
Views: 64782 oldskool funk
This is how to get those dirty hard to clean rims chrome again like they use to be God Bless Music by Gospel Gangstas, Change.
Views: 29605 oldskool funk
Automotive technician since 1991, I show an easy method for finding TOP DEAD CENTER ON THE COMPRESSION STROKE for #1 cylinder using a screw driver, hose from a compression tester and a BALLOON. Yeeeep a Balloon. its simple and can be done just by taking out the #1 spark plug. These methods work for all 4 stroke engines and will help you find that dreaded TDC on the compression stroke so you can line up your timing belt correctly. I also explain Camshaft Lobe position and why it needs to be off the lifters for compression to take place. KEEP IN MIND you DO NOT need to take the valve covers off to perform this task, I only have them off because I am changing the head gaskets on this vehicle..Another thing also, if your piston rings are bad (not sealing properly) or your valves are not seated and sealed tight you will have low compression and if it is extreme, it will not inflate the balloon. Keep your faith strong in Christ and never ever give up! Excuse me for calling the Crankshaft pulley bolt a Nut lol, I blame it on my A.D.D. lol
Views: 134054 oldskool funk
Automotive technician since 1991 I show and explain how to adjust the valve lash on a 1998 Honda Civic. This procedure will be the same for many other vehicles check your vehicle repair manual for valve lash adjustment gap because it will vary, hope this helps you God bless, put Jesus in your life
Views: 27936 oldskool funk
Yes I have a sales persons license so I can sell as many cars as I want through my partners dealership. This is the most detailed, step by step, Car flipping teaching tutorial on Youtube. I explain and show you how its done I show you my secrets and tips that took me years to fine tune. You will learn what it takes and how to sell and market your car on craigslist etc. This will be the best investment you will make for this small fee. It took me $1000s of dollar of trial and error to bring you this kind of info. You will never learn these techniques, tricks and tactics anywhere else. The information is priceless and you will not regret it I charge because It took me years to gain all this understanding and you can learn what took me years of blood sweat and hard work in 52 minutes. "The best way to compress time is to learn from the mistakes and experiences of others" Oldskool. God Bless.
This is the detailed process of how to diagnose an overheating problem (Radiator Fan not working) on a 1997 Honda Civic. This procedure works on most cars not just The civic Put Jesus at the center of it all God Bless.
Views: 523706 oldskool funk
This is the video trailer for How to make a cylinder leak down tester. The parts are cheap and it is simple to build. It is a very effective tool for diagnosing bad head gaskets bad pistons ring sealing bad exhaust valve sealing bad intake valve sealing. No need to wonder or guess anymore if you have a blown head gasket or any internal mechanical issue. Diagnose with confidence craftsmanship and 100% assurance with non assuming testing. Keep your head up God Bless.
Views: 13124 oldskool funk
Automotive technician since 1991 in this tutorial I show you the simple process of how to grind valves at home using a drill, vacuum hose and compound. it is very important that you keep the valve stem oiled and keep the compound off the valve stem work safe. stay encouraged, keep your head up and God Bless.
Views: 164435 oldskool funk
No need to take off the timing belt when changing a head gasket. Learn how to do it here and speed up the process, God Bless.
This is the cheapest and easiest way to change Mc Pherson Strut Shocks. If you ever fail or fall make sure you fall forward. Keep Jesus Christ first and at the center of you life, God Bless.
Views: 28606 oldskool funk
This is the detailed process of changing a cylinder head gasket on a 1996 Honda Civic it covers from 1996 to 2000 models. Get in attack mode and handle it with confidence, This video will walk you through step by step. Put Jesus Christ at the center and you can never go wrong, God Bless.
Views: 116138 oldskool funk
This is the most simple and cheapest way to fix a slow leaking tire and it will last for the life of the tire. Dont buy a $60-$200 tire when you can fix it for under $6 bucks. Keep your head up put Jesus Christ first and keep on SMASHIN ON IT IN HIS NAME GOD BLESS.
Views: 92355 oldskool funk
I show how to read a rich condition on spark plugs and also came across a spark plug covered with oil. This is the simple process of diagnosing if you have a fuel delivery issue and a possible valve guide or valve seal leaking in number 1 cyl.
Views: 53508 oldskool funk
In this tutorial we show you how to diagnose rotor run out, how to take off the dreade honda rotor screw and replace the brake pads. please use caution when working under your vehicle and secure it with properly.
Views: 20061 oldskool funk
This is how to fix General Motors common intake manifold gasket problems. With preparation and hard work you can attack it with confidence by using this video to help tackle your project. Put Jesus Christ at the center and stay in WARRIOR MODE in Jesus mighty name.
Views: 130141 oldskool funk
I show you how to buy spark plug wires from the wrecking yard for $1+ the junk fees a piece and how to inspect the spark plug wires. simple process to save you money, god bless
Views: 9595 oldskool funk
This is how I check for any leaking valves in a cylinder head, this method works for most valves 4 stroke or 2 stroke engines. Stay driven, Put Jesus Christ first and at the center of it all.
Views: 34183 oldskool funk
Bringing faded paint back to life is that simple
Views: 367139 oldskool funk
This is how to test a Map sensor (Manifold Absolute Pressure Sensor) on a Honda Civic. This is a very vital sensor to the engine and must be checked thoroughly in order to do a proper diagnosing of a vehicle. Keep your head up and keep Jesus Christ at the center of it all God Bless.
Views: 42071 oldskool funk
I show you how to diagnose a blown head gasket through the oil cap. But to pin point a more accurate detection a cylinder leak down test would be best because it can be a cracked head, eng block etc.
Views: 256008 oldskool funk
This is how to check for vacuum leaks when you get codes PO171 AND PO174 its simple. Put Jesus Christ at the center of it all God Bless. Ephesians 3:20 Now unto him that is able to do exceeding abundantly above all that we ask or think, according to the power that worketh in us,
Views: 116120 oldskool funk
Automotive technician since 1991 I show a quick and easy way to check your cylinder head and block deck for Warpage (gaps) using a straight edge and feeler gauge. You can also use a flash light behind and under the straight edge to see gaps ( but I highly recommend using a feeler gauge for more accuracy) Always check your repair manual for the specs on how much Warpage is acceptable (minimum & maximum tolerances). I used the 0.002 of an inch feeler gauge on this vehicle some spots went to 0.003 but it is within specs. Always clean the surface from any left over gasket material VERY WELL with a razor blade and rag before performing your inspection. GO GET IT! GOD BLESS.
Views: 20345 oldskool funk
This is a video on how we are starting a new online business called mygirlsshop.com and how we are starting more coming soon. keep Jesus Christ at the center of your life and keep on SMASHIN!
Views: 19574 oldskool funk
THIS JOB COST $500-$1000 TO FIX DEPENDING ON WHERE YOU GO. SAVE MONEY AND DO IT YOUR SELF FOR LESS THAN $8 BUCKZ. This is how you fix your Dodge Avenger 2.4L Intake manifold runners stuck open code P2004 & Intake manifold runner position sensor circuit high P2017 with Carb cleaner and WD40. Put Jesus Christ first and keep smashin on it out there, God Bless.
Views: 137518 oldskool funk
This is series #2 with more tips on how I flip cars. God Bless.
Views: 65344 oldskool funk
THIS IS HOW YOU SMASH ON LIFE. NEVER GIVE UP OR ALLOW ANYONE OR ANY CIRCUMSTANCE DURING YOUR SEASONS TO CRUSH YOUR WILL TO ENDURE. KEEP ON SMASHIN IN JESUS MIGHTY NAME. GOD IS ABLE.
Views: 5278 oldskool funk
This is how I check cylinder heads for cracks/leaks at home. Dream big, be fearless, take risk, challenge everything and put Jesus Christ at the center of it all.
Views: 298002 oldskool funk
This is my process on how I flip a car. This tutorial is for those who are struggling financially and who need to get back on their feet. I have made it simple and very easy to follow with a tons of detail, tips and tricks. Dont give up and never walk around in a defeated manner. Keep your head up high put Jesus Christ, first and God Bless.
Views: 15246 oldskool funk
OVERHEATING? This is how to take apart a restricted (clogged up) radiator and clean it for reuse. Never say the task is to great. Put Jesus Christ first and always keep him at the center of it all.
Views: 107324 oldskool funk
Automotive technician since 1991 In this tutorial I show how to make a Cylinder Leak Down Tester with simple air fittings then show you how to use it. When you perform this test do it with the engine warm if possible, the car in this video was not warm (because of repair reason) but warm your engine if you can. Have a strong day and stay bold in Jesus Name God Bless.
This is how to diagnose and test a starter God bless
Views: 36911 oldskool funk
This is how to check piston rings and valves for leaks God bless
Views: 297260 oldskool funk
I show how to find a vacuum leak with smoke, soapy water and the Long & short term fuel trim percentages.
Views: 240570 oldskool funk
This is how to fix a cracked oil pan gasket with JB WELD and how to change the oil pan gasket on a 1997 Honda Civic. This process covers 1996 to 2000 Honda Civic oil pan gaskets. God bless.
Views: 44107 oldskool funk
AUTOMOTIVE TECHNICIAN SINCE 1991 I SHOW HOW TO TIGHTEN THE TIMING BELT PROCEDURE ON A 1996 HONDA ACCORD 2.2 LITS SIMPLE. IT IS ONLY THE TIGTHENING PROCEDURE AND NOT THE INSTALLATION PROCESS. VIDEOS ON HONDA ACCORD AND CIVIC TIMING BELTS COMING SOON, GOD BLESS.
Views: 44620 oldskool funk
This is how I get free car repair information to help me diagnose and repair any car I work on, Now you can have the same information like the pros do FOR FREE. Have a strong 2016, be fearless and always put Jesus Christ first God Bless.
Views: 105943 oldskool funk
This is how to change spark plugs. so easy a 7 yr old 2nd grader can do it. Remember this DO NOT let the streets skool your kiddos because every day they are being influenced and bombarded by negativity & bad influences. Be your kid(s) influence because God gave them to you as a gift and its your job to skool them and build them up as strong young men or woman with integrity and teach them how to be leaders and to always put Jesus Christ, first God Bless
Views: 7229 oldskool funk
This is the simple compression and leak down test I do to check how bad or good the sealing of the piston rings and vales are WHILE THE ENGINES ARE OUT OF THE CAR. Time for you to seek the Lord. Keep Jesus Christ at the center of everything God Bless.
Views: 17176 oldskool funk
This is a tutorial to help inspire those who are considering being an Automotive Mechanic/ Technician in the Automotive Industry. I explain the way I did it and what it takes to become a Proficient and Competent Mechanic. It will take hard work, determination and passion in order for the new Mechanic to pave his/her way through the Automotive trade. I strongly emphasize going to school ( Automotive Technology School), Strong thorough study in Diagnostics, Electronics, Computerized Engine Controls, learning from the Wrecking Yard (to get hands on) and learning from the Oldskool Mechanics/Technicians. Chase your dreams and don't let any one kill your ambition or will to succeed in anything you want to do. The choice is yours, TAKE MASSIVE ACTION AND BE FEARLESS. With GOD (JESUS CHRIST) all things are possible.
Views: 89438 oldskool funk
have you ever tried to bleed your brakes over, and over, and you just cant seem to get the brake pedal to firm? Well This is the master cylinder bench bleeding process, how to bleed brakes with no help and fixing that dreaded spongy brake pedal that you can never get rid of. Now your problem is solved with this tutorial. Put Jesus Christ at the center of it all, God bless.
Views: 175933 oldskool funk